Chimney Repair in Edmond, OK | Edmond Chimney Sweep

Chimney Repair in Edmond - You See the Footage Before You Get a Price

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Edmond Homeowners

Most chimney problems in Edmond don’t announce themselves. A hairline crack in the crown, a loosened flashing seam, a liner that’s spalled thin behind the damper – none of it shows from the living room, and all of it gets worse with every freeze-thaw cycle our winters throw at it. That’s the problem we solve: we find what’s actually failing and carry the repair through with professional-grade materials instead of handing you off to a second contractor. Our technicians have up to 14 years of experience, and we handle the whole system, not just the part you can see. Call (844) 834-5906 to book a repair visit.

Call (844) 834-5906

Chimney Cap Installation

Chimney Cap Installation means fitting a weather-rated cover over the flue opening, and you need one the moment your chimney has no cap or the cap is a rusted hardware-store mesh cage. A proper cap does three jobs at once: it keeps rain and snow out of the flue, it stops birds and squirrels from nesting in the smoke chamber, and it keeps sparks off your roof. Oklahoma wind is hard on light covers, which is why we work with Gelco and Olympia Chimney caps built to stay put. We measure the flue, match the cap to the appliance, and mount it so it vents correctly. A cap installation typically runs $150-$450 depending on flue size and cap style, and the written estimate sets the final price.

Stainless caps for long service

Stainless steel caps hold up far better than painted steel or aluminum mesh in our part of the state. The finish doesn’t pit, and the mesh stays solid instead of sagging after a few storm seasons. We match gauge and mesh size to your appliance so the cap doesn’t restrict draft.

Multi-flue and odd-size covers

Older Edmond homes often have two flues sharing one crown, which needs a single wide cap rather than two individual units. Custom sizing handles that cleanly. We take an exact flue measurement before ordering, so there’s no back-and-forth.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is the removal of a failed cap and installation of a new one, and it’s the right call when the old cap is rusted through, bent, missing mesh, or rattling in the wind. A damaged cap is worse than no cap in some ways: loose mesh and broken welds let birds in while giving you a false sense that the flue is protected. We pull the old unit, check the flue tile and crown underneath for damage the cap was hiding, then set a new Gelco or Olympia Chimney cover sized to the opening. Chimney cap replacement in Edmond generally falls in the $150-$450 range depending on size and material, with the written estimate setting the final price.

What we check underneath

Pulling a cap is a good moment to look at the flue tile and the crown. Cracks that sat hidden under a bad cap are common, and finding them now is far cheaper than finding them after a leak. We show you photos of what we see before recommending anything.

Animal nesting and mesh damage

When a cap has been off or open for a season, birds and squirrels move in fast. We clear the nesting material, confirm the flue is unobstructed, and fit a replacement cap with intact mesh. Draft problems that looked like a fireplace issue often turn out to be a blocked flue.

Chimney Liner Installation

Chimney Liner Installation means fitting a new flue liner inside the existing chimney when the old clay tile is cracked, spalled, or simply not rated for the appliance you’re running. A liner is the barrier between combustion gases and the wood framing around your chimney, so a failed one is a genuine safety issue, not a cosmetic one. We install DuraFlex flexible liner systems because they’re made for exactly this job and conform to the flue without needing demolition. Gas inserts and modern wood stoves also often need a properly sized liner to vent correctly. Liner installation typically runs $1,800-$4,500 depending on height, flue condition, and liner size, with the written estimate setting the final price.

When a liner has to be replaced

Cracked or missing tile joints, rusted-through metal liners, and heavy glaze from years of low-temperature burning are the usual triggers. We inspect with a camera before recommending anything, and we tell you plainly when a liner can safely wait. Nothing gets replaced on a guess.

Sizing the liner to the appliance

An oversized liner drafts poorly and an undersized one chokes the appliance. We match the liner to the flue collar and the BTU output, which is where a lot of do-it-yourself jobs go wrong. Correct sizing is what makes the fireplace actually draw.

Chimney Flashing Repair

Chimney Flashing Repair deals with the metal sealing the joint where your chimney meets the roof, and you need it when you see water staining on the ceiling near the chimney, rust streaks on the flashing, or pulled-away caulk and step flashing. Flashing is the single most common source of chimney leaks, and in Edmond it takes a beating from wind-driven rain and summer hail. We reset or replace the step and counter flashing, seal the seams properly, and confirm the chase isn’t holding water. Flashing repair typically costs $200-$600 depending on roof pitch and how much of the flashing is rebuilt, with the written estimate setting the final price.

Leaks that aren’t the roof

Water near a chimney gets blamed on the shingles more often than it should. Flashing that has lifted or lost its seal lets water run straight down the masonry, and it shows up indoors far from the actual entry point. We trace the source before touching anything.

Flashings on steep pitches

Steep roofs need flashing set with more overlap and better counter-flashing detail than a shallow pitch. Getting the geometry right matters more than the material. We build the repair to suit the roof you actually have.

Chimney Crown Repair

Chimney Crown Repair fixes the concrete cap at the very top of the chimney, which is the first line of defense against water getting into the masonry. You need it when the crown is cracked, crumbled, or sloping the wrong way toward the flue instead of away from it. A failing crown lets water soak into the brick and freeze, and freeze-thaw damage is what turns a small crack into a real masonry problem. We break out the failed section and rebuild the crown with proper slope and overhang so water sheds clear of the chimney sides. Crown repair typically runs $350-$900 depending on crown size and the extent of the rebuild, and the written estimate sets the final price.

Why slope matters

A crown that’s flat or tipped toward the flue collects water right where you least want it. We form the new crown with a fall away from the flue and a drip edge past the brick. That single detail prevents most of the water damage we get called out for.

Cracking from freeze and thaw

Our winters swing hard between freezing and thawing, and water sitting in a hairline crack splits concrete a little more each cycle. Small cracks are worth sealing before they turn into a rebuild. We tell you honestly which stage yours is at.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they’ll actually take on, and many of them are sweep-only operations that refer out the moment a repair shows up. That matters when you need the work finished, not scheduled for a second visit by a different company. We handle sweeping, inspection, and repair as one practice, which means the person who diagnoses your problem is the one who fixes it. We work with an industry-vetted product portfolio including DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield, so repairs are done with manufacturer-backed materials rather than improvised ones. Repair work is priced per job; typical repairs in Edmond land in the $200-$900 range for individual items, and the written estimate sets the final price.

Questions worth asking before you hire

Ask whether they inspect with a camera and share the photos, whether they carry the repair themselves or subcontract it, and what brand of material goes into the fix. Answers to those three tell you most of what you need to know. A company that can’t answer them is a company that cleans and refers.

Why a specialist beats a handyman

A general handyman can smear sealant on a crown, but chimney repairs fail when they aren’t matched to the flue’s actual construction. Liners, crowns, and flashing all have specific requirements. We work on the whole system, and we know how the materials we use perform once they’re installed in a real chimney.

Chimney Masonry Repair

Chimney Masonry Repair addresses the brick and mortar itself, and it’s needed when you see spalled brick faces, crumbling mortar joints, or a chimney that’s leaning or separated from the house. Water is almost always the root cause: masonry soaks up moisture, the first hard freeze expands it, and the brick face flakes off. We repoint deteriorated joints, replace spalled brick, and use HeatShield resurfacing to restore a deteriorating flue liner without tearing the chimney apart. Masonry repair typically runs $400-$1,500 depending on the area involved, and the written estimate sets the final price.

Repointing versus rebuilding

Most masonry chimneys don’t need to come down, they need the mortar joints ground out and repacked properly. Repointing done right outlasts the original joint. We assess how much of the structure is actually affected before recommending anything larger.

Spalling brick and freeze damage

When brick faces pop off and leave the softer core exposed, that section can’t be saved with sealant. Those bricks get cut out and replaced with matching units. Catching it early keeps the repair small.

Brands We Service

We work with DuraFlex flexible liner systems and know where they wear – typically at the top where heat and weather meet, and at the bottom connection where the appliance collar puts stress on the seam. We also install HeatShield resurfacing material, which restores a deteriorating flue liner without the demolition a full reline sometimes requires. Knowing how these materials behave after years in a flue is what lets us choose the right one for your chimney.

On the hardware side, we fit Gelco and Olympia Chimney caps, and we service Famco venting products where they’re part of the system. Each has its own failure pattern, and we’ve seen enough of them to know what to look for before it becomes a leak or a draft problem. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Water staining on the ceiling or chimney breast. Brown rings near the chimney usually mean flashing or crown failure, and the leak gets worse with every rain. Left alone, water reaches framing.
  • Crumbling mortar or flaking brick. Spalled brick faces and sandy mortar joints signal moisture and freeze damage. Small repointing jobs stay small when they’re handled early.
  • A strong smoky smell or poor draft. Smoke rolling into the room usually points to a blocked flue or a liner problem. It’s worth diagnosing before you light another fire.
  • Visible cracks in the flue tile. A cracked liner lets heat and gases reach the chimney structure. This is the one sign that genuinely shouldn’t wait.
  • Rusted or missing chimney cap. An open flue invites birds, rain, and sparks onto the roof. A replacement cap is a small, straightforward fix.

Our Process, Step by Step

  1. 1
    Book the visit. You call and we schedule a time that works. We answer 24/7, and dispatch runs 7am to 7pm, Sunday through Friday.
  2. 2
    Inspect before we touch anything. We run a camera down the flue and look at the crown, cap, flashing, and masonry from the roof. You see the same footage we do.
  3. 3
    Explain what we found and what it means. We separate urgent safety issues from work that can safely wait, and we don’t upsell either way. If it can wait, we say so.
  4. 4
    Put it in writing. You get a written estimate with the scope and the price set per job, so there are no surprises when the work is done.
  5. 5
    Carry the repair through. Sweep, inspect, fix, done. Where the job calls for it, we install DuraFlex liners or apply HeatShield resurfacing, and we check the result before we leave.

How Much Does Chimney Repair Cost in Edmond?

Chimney repair in Edmond generally runs from about $150 for a straightforward cap installation up to $4,500 for a full liner replacement, depending on what’s actually failing. A typical cap replacement runs $150-$450. A typical crown rebuild runs $350-$900 depending on size and how much concrete is replaced. Flashing repair usually lands between $200 and $600, and masonry repointing runs $400-$1,500 depending on the area involved. Liner installation is the larger job at $1,800-$4,500 because it involves the full height of the flue and the appliance connection.

Several things move the number. Chimney height matters for any job done from the roof. Roof pitch affects how much staging flashing work needs. Access to the flue and the condition of the existing tile both change the scope. Material choice plays in too: a stainless cap costs more than painted steel, and a flexible liner sized for a wood stove differs from one for a gas insert.

How you avoid overpaying is simple: get the problem on camera before you agree to anything. Repair work recommended without evidence you can see is the main way homeowners end up paying for liner or masonry work they didn’t need. Our inspection follows the NFPA 211 inspection categories, and you get documentation you can share with an insurer or a home buyer. If the work can safely wait a season, we tell you that instead of selling it. Call (844) 834-5906 for a free estimate.

Our Service Area Near Edmond

We serve Edmond and the surrounding communities, including Guthrie, Harrah, Piedmont, Yukon, Forest Park, Luther, Nicoma Park, Langston, and Crescent. Travel time varies with distance, and we schedule visits across the area from 7am to 7pm, Sunday through Friday. If you’re outside Edmond proper, mention your town when you call so we can book the right window. You can also read more about our Edmond chimney sweep service or learn how chimney repair works in Guthrie and chimney repair in Harrah.

Serving Edmond, OK – Our Local Coverage Area

We serve Edmond and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Edmond

Schedule Your Chimney Repair Service in Edmond Today

If something about your chimney doesn’t look right, the cheapest move is finding out what’s actually going on. Call (844) 834-5906 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect with a camera, show you what we find, and tell you honestly what needs fixing now and what can wait. And when a repair is needed, we carry it through – sweep, inspect, fix, done.

Written by the team at Edmond Chimney Sweep.

Why Edmond Chooses Edmond Chimney Sweep

We set the standard for chimney repair in Edmond.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Edmond

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Edmond Customers Say

Trusted by homeowners across Edmond and surrounding areas.

★★★★★

"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."

Reggie Jackson
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Holly Mercer
★★★★★

"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."

Greg Padgett

Ready for Chimney Repair in Edmond?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Edmond.

(844) 834-5906

Request a Free Estimate in Edmond

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7